Road construction consumes large quantities of cement, aggregates, bituminous materials and fossil fuel energy. The production and transportation of these materials, together with on-site construction operations, contribute to greenhouse gas emissions. This paper examines the use of natural and waste-derived materials in rigid pavement concrete, based on the experimental programme reported in the supplied thesis. The materials considered are human hair, bamboo pieces/fibre, coconut (coir) fibre, ground granulated blast furnace slag (GGBS) and fly ash. The study compares compressive strength at different curing ages and material replacement or addition levels. The reported results indicate that human hair addition increased the 28-day M30 compressive strength from 33.60 MPa for the control mix to 37.25 MPa at 3% addition. Coconut fibre produced the highest reported 28-day strength of 40.50 MPa at 5% addition. For GGBS, the highest 28-day average strength was 34.22 MPa at 30% replacement, compared with 29.98 MPa for the control. In contrast, the bamboo series showed a progressive reduction in compressive strength as the reported replacement level increased, while fly ash replacement above 5% reduced 28-day strength in the reported series. These results demonstrate that sustainable materials must be proportioned individually rather than assumed to improve all concrete properties at every dosage. The thesis identifies potential environmental benefits through reduced use of conventional cement and aggregates and the productive use of waste resources. However, a project-specific life-cycle carbon inventory was not reported; therefore, this paper does not claim a quantified percentage reduction in CO? emissions. Further work should combine mechanical testing with a transparent life-cycle assessment and field validation.
Introduction
The study, titled “Carbon Footprint Reduction in Road Construction,” investigates the use of sustainable materials such as human hair, bamboo, coconut fibre, Ground Granulated Blast Furnace Slag (GGBS), and fly ash in rigid pavement concrete. The main objective is to reduce the environmental impact of road construction by minimising conventional cement consumption, utilising waste materials, and promoting renewable resources.
The study highlights that road construction contributes significantly to carbon dioxide emissions through cement production, aggregate processing, transportation, and the operation of construction machinery. Life-Cycle Assessment (LCA) is identified as an important method for evaluating environmental impacts throughout the construction, maintenance, and disposal stages.
Experimental investigations were conducted using different proportions of the selected materials. Concrete specimens were tested for compressive strength at different curing ages to determine the most effective replacement or addition levels.
The major findings are:
Human hair: A 3% addition produced the highest 28-day compressive strength of 37.25 MPa, representing an improvement of approximately 10.86% over the control mix.
Bamboo: Increasing bamboo content reduced compressive strength. The 2% replacement level performed better than the other modified mixes but remained below the control concrete.
Coconut fibre: A 5% addition achieved the highest 28-day compressive strength of 40.50 MPa among the tested fibre proportions.
GGBS: A 30% cement replacement produced the highest 28-day compressive strength of 34.22 MPa, approximately 14.15% higher than the control mix.
Fly ash: The 5% replacement level performed best among the modified mixes, although its 28-day compressive strength was slightly lower than that of the control concrete.
The findings demonstrate that incorporating suitable quantities of natural fibres and industrial by-products can improve certain mechanical properties of concrete while encouraging waste utilisation and reducing dependence on conventional construction materials.
However, the environmental benefits cannot be expressed as a specific reduction in CO? emissions based on compressive-strength results alone. A detailed Life-Cycle Assessment considering material production, transportation, construction, maintenance, and end-of-life impacts is necessary to quantify actual carbon savings.
Conclusion
The reported experiments show that the influence of sustainable constituents depends strongly on material type and dosage; no single percentage is suitable for all materials.
Human hair addition improved the reported M30 28-day compressive strength up to 3%, reaching 37.25 MPa compared with 33.60 MPa for the control. Strength reduced at 4%.
Coconut fibre produced its highest reported 28-day mean strength at 5% addition (40.50 MPa). The 6% mix showed a small reduction, indicating the need to control fibre dispersion and workability.
The GGBS series achieved its highest 28-day mean strength at 30% replacement (34.22 MPa), about 14.15% above the control. Strength declined sharply at 40% and 50%.
The bamboo series showed lower compressive strength as the replacement level increased. The 2% mix performed better than the 4% and 5% mixes but remained below the control.
In the fly-ash series, 5% was the best-performing replacement level, but its 28-day strength was still slightly below the control. Higher replacement levels resulted in lower reported strengths.
The use of waste-derived and industrial by-product materials has potential environmental value through resource conservation and waste utilisation. Nevertheless, the thesis does not report a quantified LCA result; carbon savings must be established through a separate life-cycle inventory and assessment.
Before field adoption, the proposed mixes require confirmation through repeat testing, durability evaluation, pavement-specific flexural performance assessment, cost analysis and field trials under actual traffic and climatic conditions.
References
[1] R. Sreedhar, P. Jichkar, and K. P. Biligiri, “Investigation of carbon footprints of highway construction materials in India,” Transportation Research Procedia, vol. 17, pp. 291–300, 2016.
[2] S. Baek et al., “Carbon reduction potential of green highway technologies in road construction,” International Journal of Pavement Engineering, vol. 16, no. 4, pp. 320–333, 2015.
[3] R. Nema, “Carbon footprint mitigation in road construction: Methods and practices in India,” International Journal of Construction Management, vol. 15, no. 4, pp. 289–302, 2015.
[4] S. Parikh, P. Modi, and A. Desai, “Bamboo as a sustainable construction material in India: Strength and cost analysis,” Journal of Green Building, vol. 11, no. 3, pp. 22–37, 2016.
[5] Y. Huang, B. Hakim, and S. Zammataro, “Measuring the carbon footprint of road construction using CHANGER,” International Journal of Pavement Engineering, vol. 14, pp. 590–600, 2013.
[6] ISO 14040:2006, Environmental Management—Life Cycle Assessment—Principles and Framework, International Organization for Standardization, Geneva, 2006.
[7] ISO 14044:2006, Environmental Management—Life Cycle Assessment—Requirements and Guidelines, International Organization for Standardization, Geneva, 2006.
[8] P. Naveen Kumar et al., “Experimental study on human hair fiber reinforced concrete (M40 grade),” International Journal of Civil Engineering Research, vol. 6, no. 3, pp. 239–248, 2015.
[9] K. Pillay, O. Olalusi, and A. Mostafa, “Paper mill waste ash as partial cement replacement in concrete for sustainable pavements,” Construction and Building Materials, vol. 263, p. 120462, 2020.
[10] A. Aliu, T. Fakuyi, and J. Williams, “Use of coconut fibers for enhancing strength and load-bearing capacity of concrete beams,” Journal of Materials in Civil Engineering, vol. 34, no. 12, p. 04022456, 2022.
[11] J. U. D. Hatmoko and L. Lendra, “Environmental impact analysis of flexible and rigid pavements using EI99 methodology,” Journal of Infrastructure Systems, vol. 27, no. 4, p. 04021048, 2021.